A fully mobile bench to provide basic airflow facilities to enable a wide range of practical airflow investigations. Suitable for demonstration, laboratory and project work at a basic level.

A round belt drive unit for use with the TM1018.

A simple eddy current damper for use with the TM165 Free Torsional Vibrations.

An experimental apparatus that allows students to investigate the oscillatory motion of a disc attached to a slender rod.

Damper pot, connecting rod and disc for use with the TM164 Free Vibrations of a Mass Spring System.

An experimental apparatus that shows students the oscillatory motion of a mass-spring system in terms of both displacement and acceleration.

An experimental apparatus that shows students how to calculate and find the centre of percussion of a compound pendulum.

An experimental apparatus that allows students to study simple harmonic motion and the factors that affect the period of oscillation of bifilar and trifilar pendulums

An experimental apparatus that allows students to study simple harmonic motion and the factors that affect the period of oscillation of pendulums.

A sturdy frame for use with TecQuipment’s Free Vibrations Experiments.

Three interchangeable governors (Hartnell, Porter and Proell) show the effects of speed, mass and geometry on governor behaviour.

A model four cylinder engine that shows the primary and secondary forces and moments when balancing reciprocating masses.

A machine to allow students to study the dynamic behaviour of different cams and followers and their "bounce" speed.

A helical gear drive unit for use with the TM1018.

A roller chain drive unit for use with the TM1018.

A toothed belt drive unit for use with the TM1018.

An experimental apparatus that allows students to investigate the oscillatory motion of a rigid beam, pivoted at one end and suspended by a spring at the other.

An ancillary unit to the TM1018 for performing acceleration tests on a simple flywheel (included) and the TM1018 gear drive unit. It also provides a facility for static friction tests on the TM1018 gear drive unit.

An experimental unit to allow students to find the dynamic efficiency of various drive types. The unit comes complete with a gear drive unit which can be configured as a simple or compound drive.

Allows Students to investigate the free and forced vibration of a rigid beam and spring, and a simply supported beam.

For experiments in centrifugal force and angular velocity.

Demonstrates the relationship between gyroscopic couple and the velocities of the rotor and precession.

For experiments in balancing a rotating mass system, statically and dynamically

A compact bench top mounting experiment to demonstrate the phenomena of whirling shafts.

Long style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine in combination with the SM1002A Extensometer. Material: Brass CZ121 (CW614N) half hard.

Long style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine in combination with the SM1002A Extensometer. Material: Aluminium alloy 2011-T3.

Long style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine in combination with the SM1002A Extensometer. Material: 0.4% carbon steel normalised.

Long style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine in combination with the SM1002A Extensometer. Material: 0.4% carbon steel as drawn.

Long style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine in combination with the SM1002A Extensometer. Material: 0.1% carbon steel normalised.

Long style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine in combination with the SM1002A Extensometer. Material: 0.1% carbon steel as drawn.

An experimental apparatus that allows students to use fundamental theory and Rayleigh’s approximation to calculate the frequency of oscillation of a cantilever.

Damper pot, connecting rod and disc, plus mounting bracket for use with the TM167 Free Vibrations of a Rigid Beam and Spring System.

A bench mounting versatile data acquisition system (VDAS) to allow computer-based data capture for a wide range of TecQuipment products.

The vortex shedding apparatus demonstrates that the drag force of water induces a suspended pendulum to shed vortices from alternate sides (a Karman vortex street).

For use with an FC300 Flow Channel, not included.

A clear acrylic, self-regulating siphon that demonstrates the automatic adjustment of its discharge over a wide range while maintaining a mostly constant water level upstream. The siphon passes a mixture of air and water.

For use with an FC300 Flow Channel, not included.

To be used with either the Spillway (FC300e) or the Ogee Weir with Tappings (FC300e2). The apparatus consists of a long apron and a selection of toothed and solid blocks that can be arranged in any combination on the apron. For the study of the dissipation of energy.

Similar to the Spillway (FC300e) but with the addition of ten pressure tappings placed over the crest and face of the weir. The tappings are connected to a suitable Manometer (FC300w) or 32-Way Pressure Display (FCA1). It is used to study the pressure differences over the crest and face of an Ogee weir.

The spillway can also be used with Energy Dissipation (FC300e3) to extend the range of possible experiments.

For use with an FC300 Flow Channel, not included.

A radial section gate for experiments to demonstrate the head/flow and discharge characteristics of a radial gate. For use with an FC300 Flow Channel, not included.

Large open channel flumes that provide the opportunity for advanced research and student study on a wide range of fluid flow topics. Select a length to suit your needs and the space available.

Large open channel flumes that provide the opportunity for advanced research and student study on a wide range of fluid flow topics. Select a length to suit your needs and the space available.

Allows easy connection of two or more modules of TecQuipment’s Modular Power System

An open circuit suction subsonic wind tunnel with a working section of 300 mm by 300 mm and 600 mm long.

An open circuit suction subsonic wind tunnel with a working section of 600 mm by 600 mm and 1250 mm long. Package includes a Three-Component Balance, Dual Axis Pressure Traverse and associated instrumentation such as a 32-Way Pressure Display Unit and Versatile Data Acquisition System (VDAS-F).

Connects other parts of TecQuipment’s Modular Power Systems range, to allow investigations into more complex electrical power systems.

Large open channel flumes that provide the opportunity for advanced research and student study on a wide range of fluid flow topics. Select a length to suit your needs and the space available.

A frame mounting versatile data acquisition system (VDAS) to allow computer-based data capture for a wide range of TecQuipment products.

A supplementary set of twenty 1g weights.

This package includes all products from the Vibration section of TecQuipment’s Theory of Machines range (TM160–TM167 and TM1016). It offers multiple experiments in both free and forced vibrations, and includes our Versatile Data Acquisition System (VDAS® mkII).

Short style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine. Material: Brass CZ121 (CW614N) half hard.

Short style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine. Material: Aluminium alloy 2011-T3.

Short style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine. Material: 0.4% carbon steel as normalised.

Short style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine. Material: 0.4% carbon steel as drawn.

Short style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine. Material: 0.1% carbon steel as normalised.

Short style specimen for use with the TecQuipment SM1002 Bench Top Tensile Testing Machine. Material: 0.1% carbon steel as drawn.

A self-contained floor standing apparatus to fully investigate the effects of speed viscosity and load on the pressure distribution in a journal bearing.

A bench mounting Michell pad apparatus to demonstrate the principle characteristics of a tilting pad slider bearing.

One set of 3 x 1500 mm weighted lengths of flume bed (with removable handles to aid fitting and removal). The bed is textured to resemble turf. Used to simulate flow over vegetated beds.

For use with an FC300 Flow Channel, not included.

Demonstrates the relationship between pressure and temperatures of a fixed volume of ideal gas.

Measures unsteady state heat transfer to bodies of different shape and thermal conductivity. Includes VDAS®.

A benchtop unit to examine the performance of a thermoelectric device for Peltier or Seebeck tests as a heat pump or generator.

Optional 16 tube finned heat exchanger for the TD1007 Water to Air Heat Exchanger unit.

Optional 16 tube heat exchanger for the TD1007 Water to Air Heat Exchanger unit.

An experimental unit to show how cross-flow water to air heat exchangers work.

An experimental apparatus to derive the temperature pressure relationship for saturated steam, and verify the Antoine Equation.

An experimental apparatus to examine free and forced convection from a flat plate, a plate with fins and a plate with rods.

Bench-top apparatus to demonstrate the behaviour and expansion processes of a perfect gas.

A benchtop unit to show the laws of radiant transfer from heat and light sources

An experimental module to show the thermal conductivity of various compatible liquids and gasses.

An experimental module to show the temperature gradient of a long thin horizontal member that is free to loose heat by natural convection and radiation.

An experimental module to introduce students to the principles of radial heat conduction, and to allow the conductivity of the test disk to be measured.

An experimental module to introduce students to the principles of linear heat conduction, and to allow the thermal conductivity of various materials to be measured.

Shows the relationship between pressure and volume of an ideal gas at a fixed temperature.

A versatile engine test bed with instrumentation to provide the facilities to investigate the operating characteristics of single-cylinder and four-stroke internal combustion engines.

A compact free-standing laboratory apparatus to allow students to investigate the theory of forced convection in pipes and associated heat transfer principles.

Digital stopwatch with 100th of a second function.

Demonstrates the forces, moments and reactions of a rigid beam.

Demonstrates concurrent and non concurrent coplanar forces. Allows students to construct force polygons and understand conditions for equilibrium.

Practical demonstration of the equilibrium of a ladder.

A demonstration to show the shape and tensions of suspension cables.

A vertical work panel printed with a metric grid. For use with the STF range of experiments.

A highly accurate and portable stroboscope providing 30 to 300,000 flashes per minute (FPM).

Provides a clean dry oil free compressed air supply for the TE3300 Series.

Tests extension springs to find their properties. Proves Hooke's law and the basic rules of spring design.

Demonstrates the failure of materials when subjected to an alternating stress.

A bench-top industrial-standard tester for accurate measurements of Vickers, Brinell and Rockwell hardness.

A bench-top industrial-standard tester for accurate measurements of Rockwell hardness.

A self-contained bench mounting experimental apparatus to enable students to investigate the distribution of radial and hoop stresses and strains throughout the wall of a thick cylinder and to compare the practical results with those predicted by theory.

A laboratory-scale steam plant that shows fundamental thermodynamic principles of energy conversion and mechanical power measurement.

A four-stoke single-cylinder petrol engine for use with TecQuipment's TD200 Small Engine Test Set.

A self-contained unit for practical examination of Hertz' theories of contact between materials. It demonstrates on a large scale the nature of contact between non-conforming bodies. For example: between the ball and race in a bearing.

A self-contained air bearing apparatus to demonstrate the performance of self-acting gas lubricated journal bearings including the phenomenon of half-speed whirl.

An experimental bench-mounting apparatus for studies into the principles and performance of heat exchangers.

Demonstrates water hammer and cavitation and the propagation of shock waves at sonic velocity in water.

Apparatus to allow students to investigate heat transfer by natural convection and radiation.

A bench mounting apparatus to allow students to investigate boiling and condensing heat transfer using water as the heat transfer medium.

A self-contained unit to demonstrate the principles of humidity measurement and to compare the relative performance and accuracies of different types of humidity measurement systems.

An apparatus to allow investigations and demonstrations into the operation and performance of a high efficiency photovoltaic cell array and battery storage system.

A portable floor standing apparatus to demonstrate and investigate the performance of a flat plate solar energy collector.

A self-contained and mobile focusing solar energy collector unit to allow practical investigations into the principles of harnessing solar energy to produce heat energy.

A computer control system to provide computer based monitoring, data logging and distributed control of compatible process control training modules in the TecQuipment TE3300 Series.

A self-contained mobile module for temperature process control experiments to illustrate the principles of single-loop control and the calibration & tuning of controllers, transmitters, converters and valves. Demonstrates feedback control, ON-OFF control, P/PI/PID control, distance-velocity lag and temperature control. Distributed control available when used with an optional computer control system.

A self-contained mobile module for level process control experiments to illustrate the principles of single-loop control and the calibration & tuning of controllers, transmitters, converters and valves. Demonstrates feedback control, P/PI/PID control and level control. Cascade control experiments available when used with an optional flow process training system. Distributed control available when used with an optional computer control system.

A self-contained mobile module for flow process control experiments to illustrate the principles of single-loop control and the calibration & tuning of controllers, transmitters, converters and valves. Demonstrates feedback control, P/PI/PID control and flow control. Cascade control experiments available when used with the optional pressure or level process training systems. Distributed control available when used with optional computer control system.

Self-contained mobile module using pressure as the control variable to illustrate the principles of single-loop control and the calibration & tuning of controllers, transmitters, converters and valves. Demonstrates feedback control, P/PI/PID control and pressure control. Cascade control available when used with the flow process training system and distributed control when used with optional computer control system software.

An optional set of additional components to extend the range of experimentation of the TE16 Stiffness of Materials and Structures Apparatus.

A four-stoke single-cylinder diesel engine for use with TecQuipment's TD200 Small Engine Test Set.

A bench mounting 3-point bend apparatus to allow investigations into the stiffness in bending of different materials of the same cross-section (Young's Modulus - Stiffness) and the stiffness of a single material with different cross-section geometries (Second Moment of Area - 'I' Value).

A small-scale bench mounting notched bar impact tester to provide students with an effective and safe introduction into commonly used material impact testing techniques such as Izod or Charpy.

Studies the accuracy, linearity and important characteristics of popular temperature measuring devices.

Small scale educational jacketed vessel and coil heat exchanger.

Small scale educational shell and tube heat exchanger.

Small scale educational plate heat exchanger.

Small scale educational tubular heat exchanger.

Service module for TecQuipment's range of bench-top educational heat exchanger demonstration units.

A four-stoke single-cylinder diesel engine with modified cylinder head and crank for use with TecQuipment's TD300 Regenerative Engine Test Bed.

A four-stoke single-cylinder petrol engine with modified cylinder head and crank for use with TecQuipment's TD300 Regenerative Engine Test Bed.

A fully instrumented exhaust gas calorimeter for use with the TD300 Regenerative Engine Test Bed to measure the heat content of engine exhaust gasses to determine the energy lost to exhaust in the energy balance for engines of various types operating at different loads and speeds.

A versatile engine test bed with instrumentation to provide the facilities to investigate the operating characteristics of compatible and interchangeable single-cylinder internal combustion engines rated up to 10 kW.

A four-stoke single-cylinder diesel engine with modified cylinder head and crank for use with TecQuipment's TD200 Small Engine Test Set.

A four-stoke single-cylinder petrol engine with modified cylinder head and crank for use with TecQuipment's TD200 Small Engine Test Set.

One set of 3 x 1500 mm weighted lengths of sand flume bed (with removable handles to aid fitting and removal). The sand
grade used is 1–2 mm. Used to simulate flow over sandy beds.

For use with an FC300 Flow Channel, not included.

A clear acrylic 60° trapezoidal flume to enable the measurement of flows with the emphasis on low flow situations.

For use with an FC300 Flow Channel, not included.

Shows and compares how resistance strain gauges work, and how they measure strains in different structures.

A set of carbon composite beams with a varied construction along their lengths. The different composition of each beam exhibiting differing bending/stiffness characteristics along its length.

An 80 mm wide 2.5 m long flow and sediment transport channel with a starter kit of models and instruments. It provides students with the ability to study the varying effects of sediment transport, bedform dynamics and fluid flow around weirs and other objects in an open channel.

TecQuipment’s Sturdy Work Bench WB1 is suitable for use with most TecQuipment bench top products.

Enhancing students’ learning and understanding of basic structural principles focusing on beams, bridges and cantilevers, these course books provide real life examples and theories and run through the experimental set-up, procedures, and analysis.

Gel Battery for use with Electric Start (ES) engines only

Strain gauged tensile specimens made from aluminium, brass and copper. For use with TecQuipment's Strain Gauge Trainer (SM1009).

TEXT HERE

A set of carbon composite beams with cored construction. The different composition of the core of each beam exhibiting differing bending/stiffness characteristics.

A set of carbon composite beams with varied construction. The different construction of each beam exhibiting differing bending/stiffness characteristics.

Pack of 10 additional beams for the SM1004 Beam Apparatus.

A set of carbon composite beams with a varied construction along their lengths. The diff erent composition of each beam exhibiting differing bending/stiffness characteristics along its length.

A set of carbon composite beams with cored construction. The different composition of the core of each beam exhibiting differing bending/stiffness characteristics.

A set of carbon composite beams with varied construction. The different construction of each beam exhibiting differing bending/stiffness characteristics.

Pack of 10 additional struts for the SM1005 Euler Buckling Apparatus.

A steel beam with eight half-bridge strain gauges spaced from the centre line, for the examination of strain at different points along a beam for both simply supported and cantilever experiments.

An optional roughened bed to extend the range of applications and experiments for the FC80 Flow & Sediment Channel Range and FC50 Flume

Software that works with TecQuipment’s VDAS-enabled products that can be used remotely, allowing students to interactively engage and participate in laboratory experiments for an adaptable, blended learning approach.

Digitally transform your practical teaching and students’ learning experience with online, interactive and guided worksheets featuring ready-made auto-graded assessments.

An automatic volumetric fuel gauge with an instrumentation unit for use with TD200 and TD300 engine test sets.

A dual-colour, gravity-fed dye injector to enable the visualisation of flow lines around obstacles in the channel.

A versatile, self-contained mobile unit designed to investigate and demonstrate the performance characteristics of a range of different pump types.

For the accurate determination of the calorific value of liquid and solid hydrocarbons.

Floor-standing apparatus with fifteen tungsten Halogen Lamps consuming up to 6 kW of power.

An ancillary to feed dry sediment directly into the FC80 channel flow from above.

An extra sluice gate, dye and accessories to enable further experimentation (for example the study of gravity waves and ice melt) for use with FC80 Flow & Sediment Channel.

A self contained floor standing unit consisting of a water reservoir and a tank for sand with overhead spray nozzles that simulate rainfall both stationary and moving. It is for studying hydrology principals including rainfall, throughflow and the movement of water over land and rivers.

This is a versatile, compact apparatus for teaching the fundamentals of kinetic wind energy conversion into electrical power. Flexibility is at the core, it has a castor-mounted frame for mobility and functionality and allows students to 3D-print their own blades for advanced experimentation.

An aerofoil suspended on springs within a frame, used to demonstrate wing flutter. The suspension positions of the wing can be altered, as can the angle of attack.

Complimentary to the air duct on the Advanced HVAC & R Trainer, this a 2 m3 environmental chamber that can be used to mimic a room.

A gravity-fed dye injector to enable the visualisation of flow lines around obstacles in the channel.

Gear Pump for use with the multi-pump test set (H85V).

A versatile, floor-standing unit for the in-depth study of heating, ventilation, air conditioning and refrigeration (HVAC & R) systems.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

8mm Lenses with a minimal focusing distance of 100mm.

Digital image correlation (DIC) system designed to enhance the student learning experience, for real-time and post-process measurement and visualisation of deformations, strains and displacements in materials and shapes. Complements the teaching equipment.

Piston Pump for use with the multi-pump test set (H85V).

Digital image correlation (DIC) system designed to enhance the student learning experience, for real-time and post-process measurement and visualisation of deformations, strains and displacements in materials and shapes. Complements the teaching equipment.

Shows how cross-flow water to air heat exchangers work.

A self-contained unit that simulates all parts of electrical power systems and their protection, from generation to utilisation.

Remotely controls and monitors TecQuipment’s Electrical Power System Simulator (PSS1) and optional Second Generator (PSS3). Teaches students how to control and supervise modern power systems

Optional 16 tube heat exchanger for the TD1007 Water to Air Heat Exchanger unit.

Mobile laboratory-scale steam turbine that demonstrates fundamental thermodynamic principles of energy conversion and mechanical power measurement.

The TecQuipment Hydro-Electric Turbine is a versatile, floor-standing, self-contained apparatus for demonstration of hydro-electricity. It is supplied with five different propellers. The product focuses on exploring the best efficiency point of different propellers and perform energy audits to analyse system performance.

A bench top base unit for demonstrating different methods of heat transfer. Requires at least one of the four optional experiments.

A generic model van and car to allow students to compare the different coefficient of drag for each vehicle. If using the optional smoke generator (AFA11) the flow of air around the vehicles can be observed.

Lobe pump for use with the Multi-Pump Test Set (H85V).

Channel Impeller Pump for use with the multi-pump test set (H85V).

Flexible Vane Pump for use with the multi-pump test set (H85V).

Axial Rotodynamic Pump for use with the multi-pump test set (H85V).

Centrifugal Pump for use with the multi-pump test set (H85V).

A seperate recirculation duct which can be fitted on the Advanced HVAC & R Trainer.

An additional load cell for the STS8 Pin-Jointed Frameworks apparatus to allow multiple loads to be simultaneously applied and measured to the test framework.

An ancillary that allows sediment to be re-circulated continually into an FC300 series flow channel from a sediment vessel located in the outlet tank.

A set of different shape models for use with the Large Subsonic Wind Tunnel (AF1600S) each with identical frontal area to allow students to compare the different coefficient of drag for each shape. Includes a dummy stem for tests to cancel out the drag due to each model’s support arm.

TEXT HERE

TEXT HERE

An experiment for investigating the force required to achieve maximum deflection of different stacking arrangements of disc springs, along with the spring rate. It fits in the Universal Testing Machine (SM1000) and consists of disc springs, a spring guide and a compression cylinder.

Five drag investigation models for use with the TecQuipment AF1300 wind tunnel - a streamlined shape, a sphere, hemisphere, "dimpled" sphere, and a flat plate. All the models have a 50mm frontal area for easy comparison

A pair of boundary layer models with a mounting plate, also a pitot and a static probe for investigating boundary layer. One plate is roughened, the other smooth to allow comparisons on boundary layer growth.

A kit of parts and instructions to upgrade either an H1 (Gravimetric Hydraulic Bench) or an H1D (Volumetric Hydraulic Bench) to an H1F (Digital Hydraulic Bench).

COMING SOON: A compact, entry level piece of equipment for visualising flow patterns around weirs and other objects in an open channel. A range of models supplied in the package makes this an ideal product for introducing students to flow visualisation in fluid mechanics.

Bench-top test set that allows students to investigate the operation and performance of a single centrifugal pump and two centrifugal pumps in both series and parallel.

COMING SOON: A highly visual demonstration of the Coriolis Force on a jet of water.

The high wing model aircraft with NACA profile wings for use with the Large Subsonic Wind Tunnel (AF1600) is good for experiments with lift, drag and pitching moment of fixed wing aircraft.

A low wing model aircraft with NACA2415 profile wings for use with TecQuipment's Large Subsonic Wind Tunnel (AF1600S)

This set of two NACA0012 aerofoils allows students to compare the results from a full-width aerofoil with a half width aerofoil.

TEXT HERE

A 150mm chord NACA2412 aerofoil with 590 span featuring a variable flap that adjusts +/- 90 degrees for use with the AF1600 Subsonic Wind Tunnel.

A 150 mm chord NACA0012 aerofoil with 595 mm span and 20 static pressure tappings.

A cylinder model that spans the full width of the working section of the AF1600S Subsonic Wind Tunnel.

This cooling column with three additional relative humidity and temperature sensors spaced through the packing, is an alternative to the standard cooling column supplied with the bench-mounted Cooling Towers experiment (EC1000).

This cooling column with no packing, acts as a spray column and is an alternative to the standard cooling column supplied with the bench-mounted Cooling Towers experiment (EC1000).

This cooling column is an alternative to the standard cooling colum supplied with the bench-mounted Cooling Towers experiment (EC1000), with a packaging density of 77 m².m^-3.

This cooling column is an alternative to the standard cooling colum supplied with the bench-mounted Cooling Towers experiment (EC1000), with a packaging density of 110 m².m^-3.

This is a digital display unit for measuring the pressure on a variety of TecQuipment experiments.

The half-circle and Vee Chine pontoons are an optional extra for the Metacentric Height and Stability experiment (H2 MKII) that allow the student to compare the stability of different hulls.

A wave generator and beach model for use with the FC300 flow channels. Allows variable control of wave frequency, as well as manual adjustment of amplitude. Demonstrates the dissipation of waves impinging on a beach.

The digital instrument carrier can precisely place the tip of the supplied instruments at any position in the x, y, and z planes of TecQuipment’s FC300 flow channel range. This data can be monitored and recorded in TecQuipment's VDAS software.

Handheld water velocity meter with display, for measuring water velocity at a point.

A 32-way pressure measurement and display unit for use with TecQuipment’s FC series flumes (FC300, FC600).

The FC300ld Lift and Drag module works with TecQuipment’s FC300 Flow Channel range. It provides a means to measure and display the lift or drag on a set of models consisting of two different sized cylinders and a hydrofoil.

TEXT HERE

Copper double shear test specimens for use with TecQuipment’s Universal Testing Machine (SM1000).

A set of 12 annealed mild steel replacement portal frames for use with STS16 Bending of Portals Apparatus.

Experiment for the study of strains, stresses, forces and deflections in various pin jointed frameworks, and the study of Bow’s notation. Mounts on the Structures platform and connects to Structures automatic data acquisition unit and software.

A set of 12 fully annealed mild steel replacement specimen beams for use with STS15 Plastic Bending of Beams apparatus.

Experiment for the study of plastic theory and limit state design in portal frames. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of determinate and indeterminate truss structures. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of rectangular portals subjected to vertical loads. Mounts on the Structures platform and connects to Structures automatic data acquisition unit and software.

Experiment for the study of the characteristics of a simple suspension bridge. Mounts on the Structures platform and connects to Structures automatic data acquisition unit and software.

Experiment for the study of bending moments and sway in portal frames. Mounts on the Structures platform and connects to Structures automatic data acquisition unit and software.

Experiment for the study of the characteristics of a suspended beam bridge. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of plastic theory and limit state design in portal frames. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of plastic theory and limit state design of beams. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for investigations into two common curved structures and two common davit structures. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment that can be used to perform a wide variety of beam experiments, from simple cases to complex problems. Mounts on the Structures test frame and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of buckling of struts and the relationships between length, end fixing conditions and buckling load. Mounts on the Structures

platform and connects to the Structures automatic data acquisition unit

and software.

Experiment for the study of the characteristics of a two-pinned arch under various load conditions. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of the characteristics of a fixed arch under various load conditions. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of strains, stresses, forces and deflections in various pin jointed frameworks, and the study of Bow’s notation. Mounts on the Structures platform and connects to Structures automatic data acquisition unit and software.

UPDATE

Experiment for the study of the vertical and horizontal defl ection of different unsymmetrical sections. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of torque and defl ection in diff erent materials with circular section. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of stress distribution across the section of a beam. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of beam deflection under different loads and fixing conditions, and the demonstration of Young’s modulus. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment for the study of stress distribution across the section of a beam. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

Experiment that illustrates and proves the basic theory of bending moments in a beam. Mounts on the Structures platform and connects to the Structures automatic data acquisition unit and software.

A benchtop platform that holds the experiments of the Next Generation Structures range

The Remote View Hardware offering from TecQuipment is a bundle containing cameras, tripods, stands and mounts for live streaming of experiments and demonstrations in the lab.

The Remote View Hardware offering from TecQuipment is a bundle containing a camera, tropod, stand and mounts for live streaming of experiments and demonstrations in the lab.

The Remote View Hardware offering from TecQuipment is a bundle containing a camera, tropod, stand and mounts for live streaming of experiments and demonstrations in the lab.

The Remote View Hardware offering from TecQuipment is a bundle containing a camera, tropod, stand and mounts for live streaming of experiments and demonstrations in the lab.

Software that works with TecQuipment’s VDAS-enabled products that can be used remotely, allowing students to interactively engage and participate in laboratory experiments for an adaptable, blended learning approach.

Software that works with TecQuipment’s VDAS-enabled products that can be used remotely, allowing students to interactively engage and participate in laboratory experiments for an adaptable, blended learning approach.

Software that works with TecQuipment’s VDAS-enabled products that can be used remotely, allowing students to interactively engage and participate in laboratory experiments for an adaptable, blended learning approach.

A sixteen channel instrument that connects to industry standard strain gauges to give direct readings of strain. Ideal for use with TecQuipment's Strain Gauge Kit (E19).

A self-contained bench mounting experimental apparatus to enable students to investigate the effect of pressure on the surface profile of a diaphragm and also the distribution of circumferential and radial strains.

A 14-tube multi-range water manometer for use with the AF10 Airflow Bench.

Multi-position Work Panel for use with TecQuipment’s Engineering Science kits.

Demonstrates the deflection of beams of different materials and dimensions, held on different supports.

Demonstrates the relationship between distances and forces in rigid beams and levers.

Demonstrates how to find the centre of gravity of shapes and the relationship between angles and coplanar forces.

Demonstrates the characteristics of coiled springs and how to test them.

Demonstrates how two popular mechanisms convert motion.

Demonstrates how rotational friction affects the efficiency of popular machine elements.

Demonstrates the relationship between centrifugal force, radius and velocity of rotating masses.

For students to assemble and understand different bar linkage mechanisms.

Demonstrates how three popular mechanisms convert motion.

Demonstrates the characteristics of the most popular gear sets.

Demonstrates the characteristics of a mechanical toggle, crank motion and the most popular shaped cams.

Demonstrates the advantages and disadvantages of three popular drive systems - belt, chain and a universal coupling.

Demonstrates the mechanical advantage of different combinations of pulleys and a simple wheel and axle.

Crank angle shaft encoder for use with ECA100 Engine Cycle Analyser to measure the angular position of the crankshafts of test engines in TecQuipment's engine test sets.

Shows the principles of tensile tests on specimens of different materials.

A cylinder head pressure transducer for use with ECA100 Engine Cycle Analyser to measure the cylinder pressures of test engines in TecQuipment's engine test sets.

A bundled set of the Engine Cycle Analyser (ECA100), a Pressure Transducer (ECA101) and a Crank Angle Encoder (ECA102).

A versatile engine cycle analyser to allow investigations into the relationship between crank angle or volume and the cylinder pressure in an internal combustion engine.

Bench-top trainer, allows students to investigate the fundamental principles of air conditioning.

Bench-top unit that allows students to investigate the stages of refrigeration.

Demonstrates the operational characteristics of an evaporative cooling tower.

A kit comprising a PVC carrying case containing a selection of resistance strain gauges together with all the necessary accessories and consumable materials associated with their application. Ideal for use with the TecQuipment SM1010 Digital Strain Display.

PVC (unplasticised) creep test specimen for use with the TecQuipment Creep Machine (SM106 or SM1006).

Nylon 66 (unfilled) creep test specimen for use with the TecQuipment Creep Machine (SM106 or SM1006).

Polypropylene creep test specimen for use with the TecQuipment Creep Machine (SM106 or SM1006).

Powerful simulation, control and data acquisition software for use with selected products from TecQuipment’s Control Engineering range.

Air compressor and reservoir to provide air for the CE107 Engine Speed Control Apparatus.

Demonstrates the torsion in circular section specimens of different materials and lengths.

Demonstrates simple harmonic motion (oscillation) in springs and pendulums, and its usefulness.

A self-contained computer based controller designed to support practical investigations into the basic and advanced principles of control engineering at all academic levels.

A pair of Venturi sides to fit into the channel allowing demonstrations of flow measurement techniques used in rivers and waterways.

For use with an FC300 Flow Channel, not included.

An optional crump weir to extend the range of applications and experiments for the FC80 Flume Range to include demonstrations of flow measurement techniques used in rivers and waterways.

An optional radial section gate to extend the range of experiments and applications for the FC80 Flume Range to include demonstrations of the head/flow and discharge characteristics of a radial gate.

An optional cylindrical gate to extend the range of experiments for the FC80 Flume Range to include demonstrations of simple underflow gate regulation.

Demonstrates flow around weirs and other objects in an open channel. Supplied with all the models and instrumentation required for a complete package in flow channel investigations.

A 20-tube manometer for measuring pressure when using the FC300 series flow channels. It mounts onto the side of the FC300 on the instrument rails.

The instrument carrier can precisely place the tip of the supplied instruments at any position in the x, y, and z planes of TecQuipment’s FC300 flow channel range.

TecQuipment’s broad crested weirs consists of two model weirs sufficiently wide to prevent the jet from springing clear at the upstream corner. The models supplied are one block with rounded upstream and downstream corners and a similar block with sharp edges. For use with FC300 Flow Channel, not included.

The notch weir set works over a range of flows to allow experiments that show the relationship between flow and head and how the weirs can be used to measure flow. The apparatus includes a holder and three standard notches, one rectangular and two “V” notch. It also includes an advanced set of two notches, Cipoletti (trapezoidal) and a Sutro notch for more experiments. For use with FC300 Flow Channel, not included.

A pair of clear culvert models, one of circular and one of rectangular section. Enabling the observation and calculation of both open and orifice flow in a culvert.

For use with an FC300 Flow Channel, not included.

A clear acrylic spillway that demonstrates the effect of a siphon spillway and the increased flow permitted when compared with an ordinary spillway of a similar height.

For use with an FC300 Flow Channel, not included.

Two sets of 3 x 1500 mm weighted lengths of gravel flume bed (with removable handles to aid fitting and removal). The small grade gravel being 2-5 mm and large grade 10 mm. Used to simulate flow over roughened beds.

For use with an FC300 Flow Channel, not included.

A pair of sediment walls and four differently profiled bridge piers. The apparatus is used to observe the increased flow velocity and the streamline curvature between the piers. Also scouring of the stream bed.

For use with an FC300 Flow Channel, not included.

A profiled base and sides to demonstrate how the flow in an open channel can be measured using a Parshall Flume.

For use with an FC300 Flow Channel, not included.

The spillway comes in four parts: the spillway, detachable ski jump and plain apron with removable toothed block. It is used to observe and calculate flow and energy dissipation over spillways.

The spillway can also be used with the Energy Dissipation (FC300e3) to extend the range of possible experiments.

For use with an FC300 Flow Channel, not included.

Demonstrates the frictional and other forces on bodies and between different surfaces on a flat or inclined plane.

A crump weir model to demonstrate alternative flow measurement techniques used in rivers and waterways. For use with FC300 Flow Channel, not included.

A sluice gate with ten tappings across its face. Enables students to investigate changes in pressure across the face of a sluice gate; also how the pressure varies with flow rate and depth. For use with an FC300 Flow Channel, not included.

Large open channel flumes that provide the opportunity for advanced research and student study on a wide range of fluid flow topics. Select a length to suit your needs and the space available.

Large open channel flumes that provide the opportunity for advanced research and student study on a wide range of fluid flow topics. Select a length to suit your needs and the space available.

A set of 5 empty trays with lids. Ideal for for additional complementary storage for the TecQuipment ES range products.

A kit containing commonly required spare items for the TecQuipment Engineering Science kits.

A mobile trolley to hold up to 24 storage trays of TecQuipment’s Engineering Science kits.

A mobile trolley with a complete set of TecQuipment’s Engineering Science kits and three Work Panels.

Contains one of each of the Simple Harmonic Motion, Friction and Inclined Plate, Potential and Kinetic Energy and Rotational Friction Kits, plus four Work Panels (ES1).

Contains one of each of the Cam, Crank and Toggle, Simple Mechanisms, Bar Linkages and Additional Mechanisms Kits, plus four Work Panels (ES1).

Contains one of each of the Pulley, Drive Systems, Gear Trains and Centrifugal Force Kits, plus four Work Panels (ES1).

Contains one of each of the Deflection of Beams, Torsion of Circular Sections, Tensile Tester and Spring Tester Kits, plus four Work Panels (ES1).

Contains one of each of the Forces and Moments Kits, plus two Work Panels (ES1).

Shows the difference between potential and kinetic energy and how it can change from one to the other.

Uses an industry standard PLC to control the PLC Process using ladder logic programming running on a PC. For use with the PLC Process (CE111).

A self-contained analogue and computer based controller designed to support practical investigations into the basic and advanced principles of control engineering at all academic levels.

An optional streamlined hump to extend the range of applications and experiments for the FC80 Flume Range to demonstrate the effects of critical flow conditions and energy loss.

A tilting 36-tube manometer for use with the AF1300, AF1450 and AF1600 Subsonic Wind Tunnels, other TecQuipment products, or as a general purpose instrument.

A 100 mm diameter flat plate for use with the AF1450 Subsonic Wind Tunnel.

A set of two aerofoils both of NACA0012 profile and 150 mm chord for use with the AF1450 Subsonic Wind Tunnel.

A 150 mm chord NACA2412 unsymmetrical section aerofoil with 300 mm span and adjustable flap for use with the AF1450 Subsonic Wind Tunnel.

A 150 mm chord 300 mm span NACA0012 aerofoil with pressure tappings for use with the AF1450 Subsonic Wind Tunnel.

A cylinder model with a single pressure tapping point for use with the AF1450 Subsonic Wind Tunnel.

An optional experiment module for use with the AF10 Air Flow Bench. For students to study boundary layers on rough and smooth flat plates. Includes a pitot to measure velocity profiles. Also allows experiments with pressure gradients.

A two-component balance to measure the lift and drag forces on models mounted in an AF1300 Subsonic Wind Tunnel.

A traversing Pitot-static tube with electronic position measurement for use with TecQuipment’s Subsonic Wind Tunnels (AF1300, AF1450, AF1600).

The 32-Way Pressure Display Unit displays up to 32 different pressures from models Pitot-static tubes and other measuring instruments fitted to a wind tunnel.

Digital differential pressure measurement and display unit for use with TecQuipment’s Subsonic Wind Tunnel (AF1300).

Measures angular positions of models mounted on TecQuipment’s Three- Component Balance (AF1300T, AF1450T or AF1600T) with the Versatile Data Acquisition System (VDAS^®).

A three-component balance designed for use with the AF1300 Subsonic Wind Tunnel.

An open circuit suction subsonic wind tunnel with a working section of 300 mm by 300 mm and 600 mm long.

An S1210 profile aerofoil of 150 mm chord for use with the AF1300 Subsonic Wind Tunnel.

A model aircraft with low wing configuration for use in TecQuipment's AF1450 Wind Tunnel.

Five drag investigation models for use with the TecQuipment AF1300 wind tunnel - a streamlined shape, a sphere, hemisphere, "dimpled" sphere, and a flat plate. All the models have a 50mm frontal area for easy comparison

A model aircraft with high wing configuration for use in TecQuipment's AF1300 Wind Tunnel.

A model aircraft with low wing configuration for use in TecQuipment's AF1300 Wind Tunnel.

A flat boundary layer model to illustrate the phenomena of boundary layer development and separation. For use with the AF1300 Subsonic Wind Tunnel.

A 100 mm diameter flat plate for use with the AF1300 Subsonic Wind Tunnel.

A set of two aerofoils both of NACA0012 profile and 150 mm chord for use with the AF1300 Subsonic Wind Tunnel.

A 150 mm chord NACA2412 unsymmetrical section aerofoil with 300 mm span and adjustable flap for use with the AF1300 Subsonic Wind Tunnel.